[RE] summit48si vlan port추가하는 법???
Reg. Date: August 20, 2004 By 김창수
추가하시려는 포트가 다른 vlan에 할당되어 있어 에러가 발생하는것입니다.
config Default delete ports 2
confi vlan vlan10 add ports 2 untagged
하시면 될것입니다.
>extreme networks summit48is vlan port 추가시 이와같은 Error가 발생하는데 Vlan Port추가하는 방법 아시는분 지도좀 부탁드리겠습니다.
>
>환절기 감기 조심하시고 는 행운이 함께 하시길 진심으로 기원드립니다.
>
>Summit48si:1 # confi vlan vlan10 add ports 2 untagged
>ERROR: There is a protocol conflict with adding port 2 untagged to
> vlan "vlan10". Either add this port as tagged or assign another
> protocol to this vlan
>
>port 2번 detail 정보입니다.
>Summit48si:3 # show ports 2 info detail
>Port 2:
> Type: UTP
> Diagnostic: passed
> Aggregate B/W: Configured 100 %
> Random Early Drop: Disabled
> Admin state: Enabled, with auto-duplex auto-speed sensing
> Link state: Ready.
> Link counter: Up 0 time(s), Down 0 times(s)
> Link Filter counter: Up 0 time(s), Down 0 times(s)
> VLAN cfg:
> Default [Internal Tag=0001,Mac-Limit:Cfg=No-limit,LRN=0,BlkHole=0]
>
> STP cfg:
> s0(disable), Tag=(none), Mode=802.1D, State=FORWARDING
>
> Trunking: Load sharing is not enabled
> Protocol: VLAN=Default Vpri=0 Protocol=ANY [EtherType:ffff]
> EDP: enabled
> DLCS: disabled
> lbdetect: disabled
> Learning: enabled
> Flooding: disabled
> Jumbo: Disabled
> BG QoS monitor: disabled
> Ingress Rate Shaping:
> QoS profile: None configured
> Queue: Q0 using QP1 MinBw=0% MaxBw=100% Pri=0.
> Q1 using QP2 MinBw=0% MaxBw=100% Pri=1.
> Q2 using QP3 MinBw=0% MaxBw=100% Pri=2.
> Q3 using QP4 MinBw=0% MaxBw=100% Pri=3.
> Q4 using QP5 MinBw=0% MaxBw=100% Pri=4.
> Q5 using QP6 MinBw=0% MaxBw=100% Pri=5.
> Q6 using QP7 MinBw=0% MaxBw=100% Pri=6.
> Q7 using QP8 MinBw=0% MaxBw=100% Pri=7.
> Ingress IPTOS: Examination is disabled
> IPTOS->QOSProfile mapping:
> 00->QP1 01->QP1 02->QP1 03->QP1 04->QP1 05->QP1 06->QP1 07->QP1
> 08->QP2 09->QP2 10->QP2 11->QP2 12->QP2 13->QP2 14->QP2 15->QP2
> 16->QP3 17->QP3 18->QP3 19->QP3 20->QP3 21->QP3 22->QP3 23->QP3
> 24->QP4 25->QP4 26->QP4 27->QP4 28->QP4 29->QP4 30->QP4 31->QP4
> 32->QP5 33->QP5 34->QP5 35->QP5 36->QP5 37->QP5 38->QP5 39->QP5
> 40->QP6 41->QP6 42->QP6 43->QP6 44->QP6 45->QP6 46->QP6 47->QP6
> 48->QP7 49->QP7 50->QP7 51->QP7 52->QP7 53->QP7 54->QP7 55->QP7
> 56->QP8 57->QP8 58->QP8 59->QP8 60->QP8 61->QP8 62->QP8 63->QP8
> Egress IPTOS: Replacement is disabled
> 802.1p Pri->IPTOS mapping:
> 0->00 1->08 2->16 3->24 4->32 5->40 6->48 7->56
> 802.1p: Disabled marking of priority field based on queue number
> Smart Redundancy: Enabled
>
> VLANs monitored for stats:
> Software redundant port: disabled
> jitter-tolerance: enabled
> auto-polarity: enabled
> link filtering: isr filter = yes, middle layer filter = no
>
>VLAN 항목입니다
>Summit48si:13 # show vlan
>Name VID Protocol Addr Flags Proto Ports
>Default 1 192.168.1.1 /24 -----T-------- ANY 0/50
>MacVlanDiscover 4095 ------------------ -------- ANY 0/0
>vlan10 4094 192.168.10.1 /24 ------f------- ANY 0/0
>vlan20 4093 192.168.20.1 /24 ------f------- ANY 0/0
>vlan30 4092 192.168.30.1 /24 ------f------- ANY 0/0
>vlan40 4091 192.168.40.1 /24 ------f------- ANY 0/0
>
>Flags: (C) Domain-masterVlan, (c) Domain-memberVlan, (d) DVMRP Enabled
> (E) ESRP Slave, (f) IP Forwarding Enabled, (G) GVRP Enabled
> (i) ISIS Enabled, (I) IP Forwarding lpm-routing Enabled
> (L) Loopback Enabled, (M) ESRP Master, (m) IPmc Forwarding Enabled
> (N) GNS Reply Enabled, (o) OSPF Enabled, (P) IPX SAP Enabled
> (p) PIM Enabled, (R) SubVLAN IP Range Configured, (r) RIP Enabled
> (S) SuperVlan, (s) SubVlan, (T) Member of STP Domain
> (v) VRRP Enabled, (V) VPLS/TLS Enabled, (X) IPX RIP Enabled
> (Z) Translation-Vlan, (z) Member-Vlan
> (2) IPX Type 20 Forwarding Enabled
>
>Total number of Vlan(s) : 6